Restore your Holosun EPS Carry Red Dot Sight

Wiki Article

Occasionally, you may want to reinitialize your Holosun EPS Carry Red Dot sight to its factory settings. This can be helpful if you've been tinkering with the adjustments or are experiencing unexpected behavior. Fortunately, resetting your Holosun is a straightforward process that can be performed in just a few procedures.

• Initially ensuring your red dot sight is turned on.
• Identify the small button for reset on the rear of the sight.
• Use a paperclip to activate the reset switch for approximately 5 seconds.
• Let go the reset button and your Holosun EPS Carry Red Dot sight will restart.
• Your red dot sight should now be set back to its factory settings.

Return to Your Holosun EPS Carry Red Dot back to Defaults

In case you've tweaked your Holosun EPS Carry red dot settings and want to go back to basics, resetting it to default configuration is a breeze. First, locate the tiny button on the side of your optic. Then, press and hold it for around twelve seconds until you see the red dot blink. Your Holosun EPS Carry is now returned to its factory settings, ready for accurate shooting.

Bring Your Holosun EPS Carry Back to : Functionality

Is your beloved Holosun EPS Carry experiencing some glitches? Don't despair! A simple factory reset can often fix the problem and get your red dot sight back to its former glory. Before you begin, remember to remove the battery from your Holosun EPS Carry to prevent unexpected activation during the process.

To perform a factory reset on your Holosun EPS Carry, follow these simple website steps:

• Hold down the power button for approximately 7 seconds.
• An indicator will flash, indicating that the reset is being performed.
• Let go of the power button once the reset is complete.

Your Holosun EPS Carry should now be back to its factory settings. You can insert the battery and confirm your sight's functionality. If you encounter any further troubles, don't hesitate to seek help from Holosun's support.

Restore Factory Settings on Your Holosun EPS Carry: A Step-by-Step Guide

Resetting your Holosun EPS Carry to factory settings can be a helpful solution if you're experiencing issues with the optic or simply want to start fresh. This process erases all user configurations and returns the sight to its original state. Before proceeding, remember to note down any customizations you have made as they will be lost during this process. Adhere to these steps carefully to ensure a successful factory reset.

• Initially, Turn on your Holosun EPS Carry by pressing the power button.
• After that, press and hold both the mode button and the up/down adjustment button simultaneously.
• As you continue holding these buttons, tap the power button once.
• You will show a confirmation prompt indicating that the reset process is initiated.
• Enable the process to finish. This may take a few moments. Once done, your Holosun EPS Carry will automatically shutdown.

After resetting your Holosun EPS Carry to factory settings, you will need to re-enter any desired customizations, such as brightness levels and reticule style. Refer to the user manual for detailed instructions on configuring your optic after a reset.

Erase All Settings on Your Holosun EPS Carry

To Original reset your Holosun EPS Carry sight, you'll need to access the settings menu. This can usually be done by Pressing a specific button combination. Consult your Instruction for the exact button sequence for your model. Once in the settings menu, look for an option that says "Factory Default". Select this option and confirm the reset. Your sight will then power off and restart with all settings Reinitialized to their default values.

Reinitialize your Holosun EPS Carry through a Factory Original Settings

If your Holosun EPS Carry is acting up, a factory reset might be the answer. This will restore your sight to its initial settings, clearing any custom configurations you've made. To execute this reset, adhere to these easy steps:

• First, locate the reset lever on your EPS Carry.
• Secondly, use a fine object, like a toothpick, to depress the reset button.
• As you maintain the reset lever pressed, power on your EPS Carry.
• The sight will blink a message indicating that the reset is finished.

After the reset is complete, your EPS Carry will be back to its factory settings.

Report this wiki page